36 practice questions with answers for CCNA interviews in Ahmedabad.
CCNA jobs in Ahmedabad
Ahmedabad and GIFT City have a growing market for IT services, fintech and product start-ups. Companies here value hands-on skills and the ability to work across tools, especially in smaller teams.
Below are 36 questions that match the mix of service, product and domain employers hiring network support engineers in Ahmedabad.
Solved for AhmedabadStart practicing
3 QUESTIONS FREESign up to unlock the full question bank and track your progress.Unlock every question and answer, then continue practising company-wise and package-wise.
✓ 3 questions free • Unlock the rest in seconds
01
Which commands would you use to test end-to-end reachability and find where packets stop?
ping tests reachability and round-trip time, and traceroute shows each Layer 3 hop.
R1# ping 10.2.2.2 source Loopback0
R1# traceroute 10.2.2.2
PC> tracert 10.2.2.2
An extended ping lets you set source, size and the DF bit to test MTU. Where traceroute shows asterisks, that hop is dropping or filtering ICMP.
02
How do you configure inter-VLAN routing on a Layer 3 switch with SVIs?
Enable routing and create an SVI per VLAN as the gateway.
ip routing
interface vlan 10
ip address 192.168.10.1 255.255.255.0
ip helper-address 10.0.0.50
no shutdown
interface vlan 20
ip address 192.168.20.1 255.255.255.0
no shutdown
show ip route connected
03
What is the difference between a two-tier and a three-tier campus design?
A three-tier design has access, distribution and core layers: access connects users, distribution aggregates access switches and applies policy, and the core provides fast transport between distribution blocks. A two-tier or collapsed-core design merges core and distribution, which suits small and medium campuses with fewer buildings. Three-tier scales better when there are many distribution blocks.
04
What are the first hop redundancy protocols and how does HSRP work?
FHRPs give hosts a virtual gateway IP shared by two or more routers. HSRP is proprietary: routers elect an active router by highest priority (default 100), and the standby takes over the virtual IP and MAC if hellos stop. Preempt lets a higher priority router reclaim the role. VRRP is the open standard, and GLBP adds load sharing across several routers.
05
Traffic is not load balancing across two equal links even though both are in OSPF. What do you check?
Both paths must have equal total cost to be installed as ECMP. I check show ip route for two next hops. If only one shows, I compare interface costs, which differ if bandwidth or the reference bandwidth differs. I also check maximum-paths. Even with ECMP, load sharing is per flow using CEF, so a single large flow uses one link only.
06
Two OSPF routers are directly connected but show no neighbour at all. How do you troubleshoot?
I check that the interfaces are up and in the same subnet, then show ip ospf interface to compare area, hello and dead timers, network type and authentication. I make sure the interface is not passive and that the network statement or ip ospf area command covers it. Finally I check that no ACL blocks protocol 89 or multicast 224.0.0.5, and use debug ip ospf adj if needed.
07
Tell me about a time you found a security issue and reported it.
Situation: during a routine audit I noticed SNMP v2c with the default community public on several access switches. Task: close the gap without disrupting monitoring. Action: I reported it to my lead with evidence, proposed SNMPv3 with an ACL, tested with the monitoring team and rolled out in two batches. Result: the risk was closed in a week and SNMP checks were added to our device baseline.
A private VLAN splits one VLAN into a primary VLAN and secondary VLANs. Isolated ports can talk only to promiscuous ports such as the gateway, while community ports can talk to each other and to promiscuous ports. It is used in hosting, DMZs and hotel networks to isolate customers on the same subnet without creating many subnets. It requires VTP transparent mode or VTP v3.
09
What are the IPv4 address classes and private ranges?
Class A is 1 to 126 with a default /8, Class B is 128 to 191 with /16, Class C is 192 to 223 with /24, Class D 224 to 239 is multicast and Class E is reserved. RFC 1918 private ranges are 10.0.0.0/8, 172.16.0.0/12 and 192.168.0.0/16. 127.0.0.0/8 is loopback and 169.254.0.0/16 is APIPA link-local. Today addressing is classless (CIDR).
DHCP uses the DORA process: the client broadcasts Discover, the server answers with an Offer, the client broadcasts a Request for that offer, and the server confirms with an Acknowledgement. The lease includes IP, mask, gateway, DNS servers and lease time. Clients renew at 50 percent of the lease. DHCP uses UDP ports 67 for the server and 68 for the client.
11
How do you back up and restore a device configuration?
Copy the config to a server and back.
copy running-config tftp://10.0.0.40/R1-backup.cfg
copy running-config scp://admin@10.0.0.40/R1.cfg
copy tftp://10.0.0.40/R1-backup.cfg running-config
configure replace flash:R1-good.cfg
archive
path flash:R1-archive
write-memory
configure replace gives a clean rollback instead of merging.
12
Guest Wi-Fi users must reach only the internet, not internal networks. How do you enforce it?
Put guests in their own VLAN and subnet, ideally terminating on a firewall or a separate VRF. Apply an inbound extended ACL on the guest SVI that permits DHCP and DNS to the allowed servers, denies all RFC 1918 destinations, and then permits any to the internet. Enable client isolation on the wireless side and rate limit the guest SSID so it cannot consume the WAN.
13
What is the native VLAN and what problems can a mismatch cause?
The native VLAN is the VLAN whose frames cross a trunk untagged, VLAN 1 by default. Both ends must use the same native VLAN; if they differ, frames leak between VLANs and CDP logs a native VLAN mismatch. For security, set the native VLAN to an unused ID, do not put users in it, and optionally tag it with vlan dot1q tag native to prevent VLAN hopping.
14
Explain the NAT terms inside local, inside global, outside local and outside global.
Inside local is the private address of an inside host, for example 192.168.1.10. Inside global is the public address that represents it outside, for example 203.0.113.5. Outside global is the real address of the remote host. Outside local is how the remote host appears to inside users, usually the same as outside global unless destination NAT is used. show ip nat translations displays these columns.
NDP uses ICMPv6 messages. A host sends a Neighbor Solicitation to the target's solicited-node multicast address (ff02::1:ffXX:XXXX) and gets a Neighbor Advertisement with the MAC. Router Solicitation and Router Advertisement messages provide prefix and gateway. Duplicate Address Detection uses NS to check that an address is unique. Using multicast instead of broadcast reduces load on other hosts.
A floating static route is a backup static route with a higher administrative distance than the primary route, so it stays out of the routing table until the primary disappears. For example, if OSPF (AD 110) learns the main path, ip route 0.0.0.0 0.0.0.0 203.0.113.1 200 installs only when OSPF loses the route. It is common for backup internet or 4G links.
17
How does controller-based networking differ from traditional networking?
Traditionally each device has its own control plane and is configured box by box. In controller-based or software-defined networking, a central controller holds the policy and pushes it to devices through southbound APIs such as NETCONF or OpenFlow, while applications talk to the controller through northbound REST APIs. This gives consistent configuration, automation and network-wide visibility.
Syslog has eight levels from 0 to 7: emergency, alert, critical, error, warning, notification, informational and debugging. A useful memory line is Every Awesome Computer Engineer Will Need Ice cream Daily. Setting logging trap 6 sends levels 0 to 6 to the server. Syslog uses UDP 514 by default, and logs should carry timestamps with service timestamps log datetime msec.
20
A PC in VLAN 20 cannot reach a PC in VLAN 30. What do you check?
First I check each PC has the correct IP, mask and gateway for its VLAN. Then I confirm the switch ports are in the right VLANs with show vlan brief, and that the trunk to the Layer 3 device allows both VLANs using show interfaces trunk. On the Layer 3 device I check the SVIs or subinterfaces are up and have the right IPs, and that no ACL blocks the traffic.
21
What are the STP port states and timers in classic 802.1D?
States are blocking, listening, learning, forwarding and disabled. Timers are hello 2 seconds, forward delay 15 seconds and max age 20 seconds. A port moves from blocking through listening and learning, each 15 seconds, so convergence can take 30 to 50 seconds. That delay is why Rapid STP and PortFast are used in modern networks.
Areas limit how far detailed LSAs flood, so SPF runs on a smaller database and changes in one area do not force recalculation everywhere. Area 0 is the backbone and every other area must connect to it, directly or through a virtual link. Routers connecting areas are ABRs and can summarize routes between areas. Single-area OSPF is the focus of CCNA.
23
How do you use CDP and LLDP to discover neighbours?
CDP is a proprietary Layer 2 discovery protocol enabled by default on IOS; LLDP is the open IEEE 802.1AB standard.
show cdp neighbors
show cdp neighbors detail
configure terminal
lldp run
show lldp neighbors detail
Detail output shows the neighbour's IP, platform and port. Disable CDP on internet-facing ports with no cdp enable.
24
Users suddenly receive IP addresses from a wrong subnet. What do you suspect and how do you fix it?
A rogue DHCP server, often a home router plugged into a wall port, is answering requests. I find it by checking the DHCP server IP on an affected client with ipconfig /all, then tracing its MAC with show mac address-table. I shut that port, and prevent it permanently by enabling DHCP snooping on user VLANs with only uplinks trusted.
25
A user complains the network is slow and the switch port shows many late collisions and CRC errors. What do you check?
Late collisions usually mean a duplex mismatch, and CRC errors point to bad cabling or interference. I would run show interfaces on the port to see duplex, speed and error counters, check the PC NIC settings, and set both sides to auto or hard-code both identically. Then I would replace the patch cable, clear counters and watch whether errors still increase.
26
Two hosts are in the same VLAN but one has mask /24 and the other /25. What problems may occur?
Each host decides local or remote using its own mask. With 192.168.1.10/24 and 192.168.1.200/25, the first thinks .200 is local and ARPs directly, but the second sees .10 as remote and sends replies to its gateway. Traffic can become one-way or asymmetric and may break completely if the gateway does not route it back. Fix the mask so both match the design.
27
Your manager wants to stop configuring 200 switches manually. What would you propose?
I would start with a source of truth for devices and variables, then use Ansible playbooks with Jinja2 templates to generate and push standard configs over SSH, keeping them in Git with peer review. A controller such as Catalyst Center could handle day-0 provisioning and compliance. I would start with read-only tasks like backups and audits, then move to small, tested change automation.
Allow web traffic from one subnet to a server and block the rest of that subnet.
ip access-list extended WEB-ONLY
10 permit tcp 192.168.10.0 0.0.0.255 host 10.0.0.80 eq 443
20 deny ip 192.168.10.0 0.0.0.255 10.0.0.0 0.0.0.255
30 permit ip any any
interface vlan 10
ip access-group WEB-ONLY in
show access-lists WEB-ONLY
Set priorities on the intended primary and secondary roots, then verify.
spanning-tree mode rapid-pvst
spanning-tree vlan 10,20 root primary
! on the backup switch
spanning-tree vlan 10,20 root secondary
show spanning-tree vlan 10
show spanning-tree root
show spanning-tree summary
30
A PC can ping its default gateway but cannot open any website. How would you troubleshoot?
Gateway reachability proves Layers 1 to 3 locally, so I move upward. I ping a public IP address; if that works but names fail, DNS is the problem, so I check the configured DNS server with ipconfig /all and test with nslookup. If the public IP also fails, I check the router's default route, NAT and upstream link. Finally I check proxy settings and any firewall blocking ports 80 and 443.
31
What is a Layer 3 switch and how is it different from a router?
A Layer 3 switch forwards packets between VLANs in hardware using SVIs or routed ports, giving very high throughput with many Ethernet ports. A router usually has fewer ports but richer WAN features such as NAT, VPN, deep QoS, varied WAN interfaces and large routing tables. In campuses, Layer 3 switches handle inter-VLAN routing while routers or firewalls handle the edge.
A voice VLAN lets an IP phone and a PC share one switch port while keeping their traffic separate. The port is an access port in the data VLAN, and the switch tells the phone through CDP or LLDP-MED to tag voice frames with the voice VLAN. This allows QoS priority for voice and separate addressing. Configure it with switchport voice vlan.
33
What are the basic steps to configure a WLAN with WPA2 or WPA3 on a controller GUI?
Steps on a typical WLC GUI: create a dynamic interface with VLAN, IP and DHCP server; go to WLANs and create a new WLAN with profile name and SSID; map it to the dynamic interface; under Security choose WPA2 or WPA3 with PSK or 802.1X and add the RADIUS server for enterprise; set QoS profile; enable the WLAN and apply it to AP groups.
Member interfaces must have the same speed and duplex, the same mode (access or trunk), the same access VLAN or the same native and allowed VLAN list on trunks, and compatible negotiation modes. Mismatched settings put members into suspended state. Configure settings on the port-channel interface so they are pushed to members, and verify with show etherchannel summary.
35
How do you check interface status and errors on an IOS device?
show ip interface brief gives status and IP of all interfaces, and show interfaces gives counters and duplex.
Router# show ip interface brief
Router# show interfaces GigabitEthernet0/1
Router# show interfaces status
Router# clear counters GigabitEthernet0/1
Status up/down means Layer 1 is up but Layer 2 keepalives fail; administratively down means the interface is shut.
36
What is a collision domain and a broadcast domain?
A collision domain is a segment where two devices sending at the same time can collide; every switch port is its own collision domain, and with full duplex collisions do not occur. A broadcast domain is the set of devices that receive a Layer 2 broadcast. Routers and VLANs separate broadcast domains, so one VLAN equals one broadcast domain.
Frequently asked questions
Which companies hire CCNA professionals in Ahmedabad?
Companies with large offices in Ahmedabad include many IT services and product firms. Use their company pages below to practise employer-specific sets.
Are CCNA interviews in Ahmedabad different from other cities?
The questions depend more on the company than the city. Ahmedabad's mix of employers decides the style: Companies here value hands-on skills and the ability to work across tools, especially in smaller teams
How do I find CCNA jobs in Ahmedabad?
Shortlist companies with Ahmedabad offices, keep your CV focused on CCNA projects, apply on company career pages and job portals with the Ahmedabad filter, and practise the questions on this page before each interview.